Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

BETAFPV Matrix 1S Brushless Flight Controller (5IN1)

Brand
Category: AIO
Kod: MS46891340
(Review Pending)
  • Power Input: 1S LiPo
  • Mounting: 26 x 26 mm
  • Dimensions: Not Specified
  • Weight: 3.92 ±0.1 g (excluding VTX antenna)
  • Continuous Current: 5A
  • Burst Current: 8A

Details

The BETAFPV Matrix 1S Brushless Flight Controller (5IN1) is an older-generation model and differs from the newer product called "Matrix 1S Brushless Flight Controller (5IN1 II)" (currently listed as "Sold Out" on the official website). It is a 5-in-1 AIO that combines an STM32G473CEU6 MCU, ICM42688P gyro (8KHz maximum sampling rate), 16MB blackbox, built-in Serial ELRS 2.4GHz receiver (CRSF; also compatible with external SBUS receivers), and built-in 5.8GHz analog VTX (25/100/200/400mW + PIT, SmartAudio 2.0). The ESC side is weaker on this model: 5A continuous / 8A burst current (lower than the 12A/18A of the 5IN1 II), supporting DShot300/DShot600, with Bluejay firmware (target: A_X_5_96KHz_V0.19.hex). UART2 is dedicated to the internal VTX, UART3 to the receiver, while UART1 and UART4 are free. The BEC output is 5V @ 3A, the mounting hole distance is 26x26mm, PCB thickness is 1.0mm, and weight is 3.92 ±0.1 g (excluding the VTX antenna). The price is 49.99 USD. The manufacturer recommends using this board with frames such as the Meteor65 Pro and Meteor75 Pro.

Box Contents

Aio: BETAFPV Matrix 1S Brushless Flight Controller (5IN1) Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    Power Input (FC):
    1S LiPo
    Mounting (FC):
    26 x 26 mm
    Dimension (FC):
    Not Specified
    Weight (FC):
    3.92 ±0.1 g (excluding VTX antenna)
    MCU (FC):
    STM32G473CEU6
    IMU(Gyro) (FC):
    ICM42688P (8KHz maximum sampling)
    USB Connection (FC):
    SH1.0-4Pin (with Type-C to SH1.0 adapter cable)
    Barometer (FC):
    Not Specified
    OSD (FC):
    Yes (AT7456E, Betaflight OSD)
    BLE Bluetooth (FC):
    Not Specified
    Flash FC Firmware Wirelessly (FC):
    Not Specified
    Download/Analyze Blackbox (FC) :
    Not Specified
    DJI Air Unit 6-pin Connector (FC):
    None (built-in analog VTX; therefore no separate connector for DJI/HD digital systems)
    Flash(for BlackBox) (FC):
    Yes (16MB)
    Current Sensor (FC):
    Yes (built-in voltage and current sensor)
    BetaFlight Camera Control Pad (FC):
    Not Specified
    5V Output (FC):
    5V @ 3A
    9V Output (FC):
    No (only 5V @ 3A BEC output is specified)
    ESC Signal Pads (FC):
    Yes (ESC1 - ESC4 motor connectors, JST1.25)
    UART (FC):
    4 UARTs (UART1 and UART4 free, UART2 dedicated to internal VTX, UART3 dedicated to receiver - CRSF or SBUS supported)
    ESC Telemetry UART (FC):
    Not Specified
    LED Pad (FC):
    Yes (RGB LED pad)
    Buzzer (FC):
    Yes (BZ+/BZ- pad)
    BOOT Button (FC):
    Yes (FC-RX-BOOT shared button pad)
    Supported Flight Controller (FC):
    Betaflight
    Firmware Target Name (FC):
    A_X_5_96KHz_V0.19.hex (ESC, Bluejay)
    Power Input (ESC):
    1S LiPo (Battery Only)
    Continuous Current (ESC):
    5A
    Burst Current (ESC):
    8A
    ESC Protocol (ESC):
    DShot300, DShot600
    Power Output (ESC):
    Not Specified
    Current Sensor (ESC):
    Not Specified (FC general voltage/current sensor available; no dedicated ESC-specific sensor specified)
    Firmware (ESC):
    Bluejay (ESC, target: A_X_5_96KHz_V0.19.hex); ELRS V3.4.3 (receiver)