Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

T-MOTORHOBBY F411 AIO 1S 6A ELRS VTX BLUEJAY

Brand
Category: AIO
Kod: MS46891340
(Review Pending)
  • Power Input: 1S LiPo
  • Mounting: 25.5x25.5mm / M2
  • Dimensions: 29.5x29.5mm
  • Weight: 6.7g
  • Continuous Current: 6A x4
  • Burst Current: 7A x4

Details

T-MOTORHOBBY F411 AIO 1S 6A ELRS VTX BLUEJAY is a compact AIO board that combines an FC, 6A 1S 4-in-1 ESC, integrated SPI ELRS 2.4G receiver, integrated 50mW analog VTX, and integrated analog VTX OSD chip on a single board. It uses an STM32F411 MCU and BMI270 gyro. The ESC comes with Bluejay firmware pre-installed from the factory, with an advertised efficiency improvement of up to 20%. The ELRS receiver features an integrated antenna on the board, providing faster response, a compact design, and a strong signal. The VTX provides 48 channels at 50mW and supports SmartAudio 1.0. An antenna can be replaced through the UFL connector. Users who want to use an external VTX can disable the integrated VTX by soldering the two pads labeled "OFF" on the board. Recommended motors include the T-Motor M0803/M0802, which connect directly through plug-and-play connectors without soldering. The camera must be soldered to the board. The official wiring diagram also shows connections for an external SBUS or TBS Crossfire Nano receiver as an alternative to the integrated ELRS receiver. The package includes 6x silicone vibration-damping washers, 1x VTX antenna, and 1x BT2.0 power cable. The product page provides only one downloadable resource, "F411-06A-VTX-TABLE.zip", which is likely a VTX frequency table. No comprehensive manual PDF has been published.

Box Contents

Aio: T-MOTORHOBBY F411 AIO 1S 6A ELRS VTX BLUEJAY Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    Power Input (FC):
    1S LiPo
    Mounting (FC):
    25.5 x 25.5 mm / M2
    Dimension (FC):
    29.5 x 29.5 mm
    Weight (FC):
    6.7 g
    MCU (FC):
    STM32F411
    IMU(Gyro) (FC):
    BMI270
    USB Connection (FC):
    Micro USB
    Barometer (FC):
    Not specified
    OSD (FC):
    Yes (Betaflight OSD, with AT7456Ev chip; displays real-time flight information)
    BLE Bluetooth (FC):
    Not specified
    Flash FC Firmware Wirelessly (FC):
    Not specified
    Download/Analyze Blackbox (FC) :
    Not specified
    DJI Air Unit 6-pin Connector (FC):
    Not specified (a general connector with SWITCH/5V-IN/GND/DATA/CAM/VTX pads is provided for an external VTX; two additional pads must be soldered to disable the integrated VTX)
    Flash(for BlackBox) (FC):
    Not specified
    Current Sensor (FC):
    Not specified
    BetaFlight Camera Control Pad (FC):
    Not specified
    5V Output (FC):
    5V @ 1A
    9V Output (FC):
    None
    ESC Signal Pads (FC):
    M1 - M4 motor pads
    UART (FC):
    R2/T2 pads (full UART number not specified)
    ESC Telemetry UART (FC):
    Not specified
    LED Pad (FC):
    Not specified
    Buzzer (FC):
    Not specified
    BOOT Button (FC):
    Not specified
    Supported Flight Controller (FC):
    Not specified
    Firmware Target Name (FC):
    Not specified
    Power Input (ESC):
    1S LiPo
    Continuous Current (ESC):
    6A (per channel)
    Burst Current (ESC):
    7A (per channel)
    ESC Protocol (ESC):
    Not specified
    Power Output (ESC):
    Not specified
    Current Sensor (ESC):
    Not specified
    Firmware (ESC):
    Bluejay (ESC, factory-installed)