Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

T-MOTORHOBBY F411 AIO 1S 13A BL32

Brand
Category: AIO
Kod: MS46891340
(Review Pending)
  • Power Input: 1S LiPo
  • Mounting: 25.5x25.5mm / M2
  • Dimensions: 29.5x29.5mm
  • Weight: 5.7g
  • Continuous Current: 13A x4
  • Burst Current: Not specified

Details

T-MOTORHOBBY F411 AIO 1S 13A BL32 is a compact FC+ESC all-in-one board designed for 1S racing whoops and 1S long-range toothpick builds. It uses an STM32F411 MCU with a 32-bit M4 core and a BMI270 gyro. It provides 13A continuous current per channel, uses AM32 ESC firmware, and supports an adjustable PWM frequency from 24K to 96K. An integrated 8MB blackbox memory based on a Winbond flash chip is included. Customizable ESC startup sounds are supported. The wiring diagram shows compatibility with an SBUS receiver, TBS Crossfire Nano receiver, and a digital VTX module with SWITCH, 5VIN, GND, DATA, CAM, and VTX pads. Dedicated VIDEO/5-36V/GND pads are also available for an analog camera. LED, buzzer (BZ-), and BOOT pads are present on the board. The package includes 6x silicone vibration-damping washers, 5x motor connector plugs, 1x PH2.0 power cable, and 1x BT2.0 power cable. Note: T-Motor has not published a downloadable manual PDF for this product. All information has been compiled from the marketing images on the product page.

Box Contents

Aio: T-MOTORHOBBY F411 AIO 1S 13A BL32 Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    Power Input (FC):
    1S LiPo
    Mounting (FC):
    25.5 x 25.5 mm / M2
    Dimension (FC):
    29.5 x 29.5 mm
    Weight (FC):
    5.7 g
    MCU (FC):
    STM32F411 (32-bit M4 core)
    IMU(Gyro) (FC):
    BMI270
    USB Connection (FC):
    Micro USB
    Barometer (FC):
    Not specified
    OSD (FC):
    Not specified (VI/VO video input/output pads are available for an analog camera; no separate OSD chip is specified)
    BLE Bluetooth (FC):
    Not specified
    Flash FC Firmware Wirelessly (FC):
    Not specified
    Download/Analyze Blackbox (FC) :
    Not specified
    DJI Air Unit 6-pin Connector (FC):
    Not specified (a general connector/pad layout for digital VTX with SWITCH/5VIN/GND/DATA/CAM/VTX is provided, but it is not identified as a dedicated 6-pin DJI connector)
    Flash(for BlackBox) (FC):
    8 MB
    Current Sensor (FC):
    Not specified
    BetaFlight Camera Control Pad (FC):
    Not specified (VTX control pad T1 is available)
    5V Output (FC):
    5V (shared power supply for LED, VTX, and receiver; current rating not specified)
    9V Output (FC):
    None
    ESC Signal Pads (FC):
    Not specified
    UART (FC):
    Not specified
    ESC Telemetry UART (FC):
    Not specified
    LED Pad (FC):
    Available
    Buzzer (FC):
    Available (BZ- pad)
    BOOT Button (FC):
    Available
    Supported Flight Controller (FC):
    Not specified
    Firmware Target Name (FC):
    Not specified
    Power Input (ESC):
    1S LiPo
    Continuous Current (ESC):
    13A (per channel)
    Burst Current (ESC):
    Not specified
    ESC Protocol (ESC):
    Not specified
    Power Output (ESC):
    Not specified
    Current Sensor (ESC):
    Not specified
    Firmware (ESC):
    AM32 (ESC firmware); PWM frequency adjustable from 24K to 96K