Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

FETtec AIO 35A - N

Brand
Category: AIO
Kod: MS46891340
(Review Pending)
  • Power Input: 3S - 6S LiPo (12-25V)
  • Mounting: 20 x 20 mm (M2, expandable to M3)
  • Dimensions: 30 x 37.5 mm
  • Weight: 8.9 g
  • Continuous Current: 35A x4
  • Burst Current: Not specified

Details

The FETtec AIO 35A - N is the version of the standard FETtec AIO 35A without an integrated analog OSD. The rest of the hardware is identical, including the STM32G4 170MHz flight controller processor, MPU6000 gyro, STM32G071 64MHz ESC, dual 5V / 5V-16V BEC, 8-pin VTX/camera connector, dimensions, mounting, and weight. It comes with KISS FC firmware from the factory and can also be flashed with FETtec Alpha FC firmware (KISS firmware version 1.3RC47i or newer is required). Since there is no integrated OSD, UART4 is completely free. A separately sold FETtec OSD Board accessory can be used for analog OSD and is connected via Serial1. Digital OSD systems work normally. Configuration is performed via the Micro USB port, as confirmed in the official manual diagram. An I2C OLED display (128x64px, recommended 1.3-inch SSH1106) allows configuration without a computer; this connection occupies Serial3. Flight log files can be retrieved using OpenLager/OpenLog, which is available as a separate accessory. The box includes a 50V 470uF capacitor, two 4-pin cables, one 8-pin cable, and standoffs. Note: The product is currently out of stock on the manufacturer's website.

Box Contents

1. Open Aio Manual in a New Tab
Click here to open the Aio Manual in a new tab
2. Download Aio Manual
Click here to download the Aio Manual
Aio: FETtec AIO 35A - N Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    Power Input (FC):
    3S - 6S LiPo (12-25V)
    Mounting (FC):
    20 x 20 mm (M2, expandable to M3)
    Dimension (FC):
    30 x 37.5 mm
    Weight (FC):
    8.9 g
    MCU (FC):
    STM32G4 (170MHz + math accelerator, FC) + STM32G071 (64MHz, ESC)
    IMU(Gyro) (FC):
    MPU6000
    USB Connection (FC):
    Micro USB
    Barometer (FC):
    Not specified
    OSD (FC):
    None
    BLE Bluetooth (FC):
    Not specified
    Flash FC Firmware Wirelessly (FC):
    Not specified
    Download/Analyze Blackbox (FC) :
    Available (with OpenLager/OpenLog, separate accessory)
    DJI Air Unit 6-pin Connector (FC):
    Not specified
    Flash(for BlackBox) (FC):
    Not specified
    Current Sensor (FC):
    Not specified
    BetaFlight Camera Control Pad (FC):
    Not specified
    5V Output (FC):
    2x 5V (fixed for RX; switched 5V/16V for VTX; max. 600mA each)
    9V Output (FC):
    None
    ESC Signal Pads (FC):
    Motor 1-4 pads
    UART (FC):
    5 UARTs (UART1 free, UART2 receiver, UART3 free, UART4 completely free, UART5 ESC/TLM/Onewire)
    ESC Telemetry UART (FC):
    UART5
    LED Pad (FC):
    Available
    Buzzer (FC):
    Not specified
    BOOT Button (FC):
    Available
    Supported Flight Controller (FC):
    KISS FC firmware, FETtec Alpha FC firmware
    Firmware Target Name (FC):
    Not specified
    Power Input (ESC):
    3S - 6S LiPo
    Continuous Current (ESC):
    35A (per channel)
    Burst Current (ESC):
    Not specified
    ESC Protocol (ESC):
    PWM, Oneshot125/42, DShot150/300/600/1200/2400, FETtec Onewire
    Power Output (ESC):
    Not specified
    Current Sensor (ESC):
    Not specified
    Firmware (ESC):
    KISS FC firmware / FETtec Alpha FC firmware (FC), FETtec ESC Firmware (ESC)