Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

BETAFPV F4 1S 5A AIO Brushless Flight Controller

Brand
Category: AIO
Kod: MS46891340
(Review Pending)
  • Power Input: 1S LiPo (with BT2.0 connector, 55mm cable)
  • Mounting: 26 x 26 mm
  • Dimensions: 30 x 30 mm (PCB), 0.8mm thickness
  • Weight: 3.64 g (Classical) / 2.96 g (Light)
  • Continuous Current: 5A
  • Burst Current: 6A (3 seconds)

Details

The BETAFPV F4 1S 5A AIO Brushless Flight Controller is a separate, lighter, entry-level product compared to the previously added F4 1S 12A V3 and F4 2-3S 20A products. It uses a single STM32F411CEU6 (100MHz) MCU option (unlike the dual F405/AT32F435 options of the 12A V3), features a BMI270 gyro instead of the ICM42688P, has no built-in barometer, and uses a pure 1S power input with a 55mm cable and BT2.0 connector instead of XT30. Two different receiver (RX) versions are available: Serial ELRS 2.4G (CRSF protocol, supports ELRS V3.0+, wireless firmware updates via WiFi or serial passthrough through the ESP8285 chip, 39.99 USD) and SPI Frsky (D8/D16 FCC/LBT, Futaba S-FHSS, CC2500 chip, flashable only through Betaflight Configurator, discounted to 27.99 USD). It is also available in two body versions: Classical (with soldered motor connectors, 3.64g) and Light (unsoldered, with detachable motor pins, 2.96g). It features a built-in AT7456E OSD chip (a separate OSD chip could not be identified on the 12A V3). The ESC is rated at 5A continuous / 6A burst (3 seconds), making this the lowest-power AIO added so far. The PCB measures 30x30mm and is 0.8mm thick, while the mounting hole spacing is 26x26mm, the same as the other products.

Box Contents

Aio: BETAFPV F4 1S 5A AIO Brushless Flight Controller Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    Power Input (FC):
    1S LiPo
    Mounting (FC):
    26 x 26 mm
    Dimension (FC):
    30 x 30 mm (PCB), 0.8mm thickness
    Weight (FC):
    3.64 g (Classical, with soldered motor connectors) / 2.96 g (Light, unsoldered, with detachable motor pins)
    MCU (FC):
    STM32F411CEU6 (100MHz)
    IMU(Gyro) (FC):
    BMI270 (6-axis)
    USB Connection (FC):
    Not Specified (the official page does not explicitly specify the USB type; a connector labeled "USB Port" is visible in the pinout image)
    Barometer (FC):
    Not Specified
    OSD (FC):
    Yes (AT7456E, built-in Betaflight OSD)
    BLE Bluetooth (FC):
    Not Specified
    Flash FC Firmware Wirelessly (FC):
    Yes (only on the Serial ELRS 2.4G version; wireless firmware updates via WiFi or Betaflight serial passthrough through the ESP8285 chip and WiFi antenna; this feature is not available on the SPI Frsky version, which can only be flashed through Betaflight Configurator)
    Download/Analyze Blackbox (FC) :
    Yes (8MB internal flash blackbox memory)
    DJI Air Unit 6-pin Connector (FC):
    No (there is no DJI PMU connector; an external analog VTX - TBS SmartAudio - or external HD digital VTX - Configuration/MSP - can be connected through UART2)
    Flash(for BlackBox) (FC):
    Yes (8MB)
    Current Sensor (FC):
    Not Specified
    BetaFlight Camera Control Pad (FC):
    Not Specified
    5V Output (FC):
    Not Specified (the official page does not separately specify the BEC current rating)
    9V Output (FC):
    No
    ESC Signal Pads (FC):
    Yes (ESC1 - ESC4)
    UART (FC):
    The SPI Frsky version also includes an SBUS port; UART1 can be used for an external serial receiver (must be disabled when using the SPI receiver), while UART2 is assigned to the VTX (TBS SmartAudio for analog VTX, Configuration/MSP for HD digital VTX). One pinout variant also shows dedicated RX1/TX1/SBUS pads
    ESC Telemetry UART (FC):
    Not Specified
    LED Pad (FC):
    Yes (LED pad; also includes built-in FC LED - Blue, RX LED - Green, and Mode LED - Orange on the ELRS version)
    Buzzer (FC):
    Not Specified
    BOOT Button (FC):
    Yes (BOOT/BIND button)
    Supported Flight Controller (FC):
    Betaflight
    Firmware Target Name (FC):
    Betaflight 4.3.0 (Serial ELRS 2.4G version); Betaflight 4.2.11 (SPI Frsky version); A_X_5_.HEX (ESC, Bluejay BB51)
    Power Input (ESC):
    1S LiPo (with BT2.0 connector, 55mm cable)
    Continuous Current (ESC):
    5A
    Burst Current (ESC):
    6A (3 seconds)
    ESC Protocol (ESC):
    DShot300, DShot600
    Power Output (ESC):
    Not Specified
    Current Sensor (ESC):
    Not Specified
    Firmware (ESC):
    Betaflight 4.3.0 (FC, ELRS version); Betaflight 4.2.11 (FC, Frsky version); Bluejay BB51 (ESC, target: A_X_5_.HEX); ELRS (built-in receiver firmware on the Serial ELRS 2.4G version)