Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

BETAFPV Matrix 1S Brushless Flight Controller (AIO P1 HD VTX) [BETA TEST]

Brand
Category: AIO
Kod: MS46891340
(Review Pending)
  • Power Input: 1S LiPo (with BT2.0 connector)
  • Mounting: 25.5 x 25.5 mm
  • Dimensions: 30.5 x 30.5 mm (PCB), 1.0 mm thickness
  • Weight: 4.60 g (FC only) / 5.99 g (including Air HD Camera)
  • Continuous Current: 12A
  • Burst Current: 18A

Details

[BETA TEST] BETAFPV Matrix 1S Brushless Flight Controller (AIO P1 HD VTX) is fundamentally different from all Matrix/Air/F4 products added so far: it features its own integrated digital HD VTX transmitter (P1 Air Unit), eliminating the need for an external DJI O3/O4, Walksnail, HDZero, or Caddx Vista HD VTX module. The P1 Air Unit uses the Artosyn AR803X chip and BETAFPV proprietary "ArtLynk Protocol" digital transmission system (with KAP - Key Antenna Protocol support), operating in the 5.1-5.9GHz frequency range at 200mW power, 1080p@60fps resolution, and approximately 60ms latency. This product is officially classified as a "BETA TEST" product; it comes pre-flashed with P1 Air Unit firmware v2.1.1, and the official page states that receiver (ground) devices must be updated to v2.1.2 for compatibility. The mounting hole spacing is 25.5 x 25.5mm, the same as the Matrix 1S 3IN1/4IN1 HD, but unlike that product, this board has an integrated VTX. The camera connects through a dedicated DF36-15 connector instead of a standard CAM flex pad (Air HD Camera, 153° FOV, 1.34g). The MCU is STM32G473CEU6 and the gyro is BMI270 (rather than the ICM42688P used in other Matrix products). The board also features a dedicated "P1 Bind Button" (VTX pairing) and an "FC & RX BOOT" button — these two separate buttons indicate that FC/ESC boot operations and P1 Air Unit pairing are independent of each other.

Box Contents

Aio: BETAFPV Matrix 1S Brushless Flight Controller (AIO P1 HD VTX) [BETA TEST] Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    Power Input (FC):
    1S LiPo
    Mounting (FC):
    25.5 x 25.5 mm
    Dimension (FC):
    30.5 x 30.5 mm (PCB), 1.0 mm thickness
    Weight (FC):
    4.60 g (FC only) / 5.99 g (including Air HD Camera)
    MCU (FC):
    STM32G473CEU6
    IMU(Gyro) (FC):
    BMI270 (3.2kHz sampling)
    USB Connection (FC):
    SH1.0-4Pin
    Barometer (FC):
    Not specified
    OSD (FC):
    None (according to the official page, this product does not have Betaflight OSD; display information is presumably handled by the P1 Air Unit digital VTX system)
    BLE Bluetooth (FC):
    Not specified
    Flash FC Firmware Wirelessly (FC):
    Not specified
    Download/Analyze Blackbox (FC) :
    Yes (16MB internal flash blackbox memory)
    DJI Air Unit 6-pin Connector (FC):
    No (no DJI/external HD VTX connector is required; the product features its own integrated P1 Air Unit digital VTX transmitter - Artosyn AR803X chip, ArtLynk Protocol, 5.1-5.9GHz, 200mW, 1080p@60fps, ~60ms latency, IPEX antenna pad - P1 ANT)
    Flash(for BlackBox) (FC):
    Yes (16MB)
    Current Sensor (FC):
    Yes (voltage and current sensor, labeled "Current Sensor" on the pinout diagram)
    BetaFlight Camera Control Pad (FC):
    Not specified
    5V Output (FC):
    5V @ 3A (maximum)
    9V Output (FC):
    No
    ESC Signal Pads (FC):
    Yes (ESC1 - ESC4, with EFM8BB51 chips)
    UART (FC):
    UART2 is externally available for general use (RX2/TX2 pads); UART3 is dedicated to the internal Serial ELRS receiver, while UART4 is dedicated to the internal P1 Air Unit HD VTX
    ESC Telemetry UART (FC):
    Not specified
    LED Pad (FC):
    Yes (RGB LED pad: LED-RGB-5V-GND)
    Buzzer (FC):
    Yes (BZ+/BZ- pad)
    BOOT Button (FC):
    Yes (two separate buttons: "FC & RX BOOT" and a separate "P1 Bind Button" for the P1 Air Unit)
    Supported Flight Controller (FC):
    Betaflight
    Firmware Target Name (FC):
    Not specified (FC firmware target name is not provided on the official page); BETAFPV 2.4G AIO V2 RX (receiver firmware); A_X_5_96KHz_V0.19.hex (ESC, Bluejay BB51); P1 Air Unit firmware v2.1.1 (factory installed, ground devices must be updated to v2.1.2)
    Power Input (ESC):
    1S LiPo (BT2.0 connector)
    Continuous Current (ESC):
    12A
    Burst Current (ESC):
    18A
    ESC Protocol (ESC):
    DShot300, DShot600
    Power Output (ESC):
    5V @ 3A (maximum)
    Current Sensor (ESC):
    Not specified (the FC has a general voltage/current sensor, but no separate ESC-specific value is specified)
    Firmware (ESC):
    BETAFPV 2.4G AIO V2 RX (receiver firmware); Bluejay BB51 (ESC, target: A_X_5_96KHz_V0.19.hex); P1 Air Unit v2.1.1 (VTX firmware, factory installed)