Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

GEPRC TAKER F405 BLS 100A 8S STACK

Brand
Category: Stack
Kod: MS46891340
(Review Pending)
  • Power Input: 3-8S LiPo (FC), 3-8S LiPo (ESC)
  • Continuous Current (ESC): 100A
  • Mounting (FC and ESC): 30.5x30.5mm
  • MCU: STM32F405
  • BEC: 5V@3A + 12V@3A
  • Burst Current (ESC): 105A (5 seconds)

Detail

The GEPRC TAKER F405 BLS 100A 8S STACK is a stack made of the GEP-F405-8S flight controller with an STM32F405 processor and the TAKER H100_8S_BLS 100A 4in1 ESC. Flight controller: ICM42688-P gyro (SPI), 16MB Blackbox, barometer, integrated LC filter, Type-C USB, direct plug-in connector for the DJI Air Unit, BetaFlight OSD (AT7456E), dual independent BEC (5V@3A + 12V@3A), 6 UARTs, 8 motor outputs (M1-M8), input 3-8S LiPo, size 37x37mm, mounting 30.5x30.5mm, weight 8.3g, firmware target GEPRCF405_8S. ESC: TAKER H100_8S_BLS 100A 4in1, input 3-8S LiPo, ammeter (calibration value 200), 100A continuous, 105A burst (5 s), DShot150/300/600, size 56.3x61.1mm, 30.5x30.5mm mounting (φ4mm hole, φ3mm with silicone dampers), weight 28.8g, ESC target B_X_30. The damped mounting keeps the gyro stable. Note: The manufacturer page lists the ESC target as "B_X_3" for this product; the same ESC (TAKER H100_8S_BLS) is listed as "B_X_30" on the F722 stack page, so B_X_30 is used here. On Oct 20, 2025 the manufacturer changed the FC firmware to GEPRCF405_8S.

Box contents

  • 1 x flight controller, 1 x TAKER H100_8S_BLS 100A 4in1 ESC, 1 x electrolytic capacitor (50V 4700uF), DJI connection cable (SH1.0 6pin 100mm), 2 x FC adapter cable (SH1.0 8pin 30mm), receiver cable (SH1.0 4pin 150mm), camera cable (SH1.0-SH1.25 3pin 135mm), VTX cable (SH1.0 4-6pin 100mm), 1 x XT90 battery plug, red and black power cable (10AWG 240mm), 4 x M3*30 and 4 x M3*25 screws, 8 x M3 nylon nuts, 12 x M3 silicone anti-shake pads
1. Open STACK Manual in a New Tab
Click here to open the STACK Manual in a new tab
2. Download STACK Manual
Click here to download the STACK Manual
STACK: GEPRC TAKER F405 BLS 100A 8S STACK Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU (FC):
    STM32F405
    IMU(Gyro)(FC):
    ICM42688-P
    USB Port Type (FC):
    Type-C
    Barometer (FC):
    Supported
    OSD Chip (FC):
    AT7456E
    BLE Bluetooth (FC):
    No
    DJI Air Unit Connection Way (FC):
    DJI Air Unit plug-and-play connector
    6-pin DJI Air Unit Plug (FC):
    Supported
    Flash(for BlackBox) (FC):
    16MB
    BetaFlight Camera Control Pad (FC):
    Not specified by manufacturer
    Power Input (FC):
    3-8S LiPo
    5V Output (FC):
    5V@3A
    9V Output (FC):
    12V@3A
    3.3V Output (FC):
    Not specified by manufacturer
    4.5V Output (FC):
    Not specified by manufacturer
    ESC Signal Pads (FC):
    8 motor outputs (M1-M8)
    UART (FC):
    6 UARTs
    ESC Telemetry UART (FC):
    Not specified by manufacturer
    LED Pad (FC):
    Not specified by manufacturer
    Buzzer (FC):
    Not specified by manufacturer
    BOOT Button (FC):
    Not specified by manufacturer
    Supported Flight Controller Firmware (FC):
    Betaflight
    Firmware Target Name (FC):
    GEPRCF405_8S
    Mounting (FC):
    30.5x30.5mm (φ4mm hole, φ3mm with silicone dampers)
    Dimension (FC):
    37x37mm
    Weight (FC):
    8.3g
    Firmware (ESC):
    FC: GEPRCF405_8S / ESC: B_X_30 (BLHeli_S)
    PC Configurator Download Link (ESC):
    https://github.com/betaflight/betaflight-configurator/releases
    Continuous Current (ESC):
    100A
    Burst Current (ESC):
    105A (5 seconds)
    TVS Protective diode (ESC):
    Not specified by manufacturer
    External Capacitor (ESC):
    50V 4700uF electrolytic capacitor included
    ESC Protocol (ESC):
    DShot150/300/600
    Power Input (ESC):
    3-8S LiPo
    Power Output (ESC):
    Not specified by manufacturer
    Current Sensor (ESC):
    Supported (ammeter, calibration 200)
    ESC Telemetry (ESC):
    No (BLHeli_S ESCs do not support telemetry)
    Mounting (ESC):
    30.5x30.5mm (φ4mm hole, φ3mm with silicone dampers)
    Dimension (ESC):
    56.3x61.1mm
    Weight (ESC):
    28.8g