Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

HGLRC SPECTER F760 BOX integrated stack

Brand
Category: Stack
Kod: MS46891340
(Review Pending)
  • Power Input: FC 7.4V-22.8V (2-6S) / ESC 3-6S
  • Continuous Current (ESC): 60A
  • Mounting (FC and ESC): 20x20mm / M3
  • Dimensions: (Stack) 44.2x30x21.15mm
  • Weight: ~39.24g (stack, without accessories)
  • Burst Current (ESC): 65A (10 seconds)

Detail

The HGLRC SPECTER F760 BOX is an integrated stack designed to make installation easier, combining the FC and a 60A 4in1 ESC inside a CNC aluminum heat sink shell. The flight controller is fully modular with plug-and-play connections; only the ESC power and motor wires need to be soldered. It features an STM32F722 (216MHz) processor, MPU6000 gyro, AT7456E OSD, BMP280 barometer and a 16MB black box. Built-in Betaflight Bluetooth allows port and PID tuning from the SpeedyBee app. It has a 10V electronic switch that can be turned on/off via Betaflight (enabled by default), a built-in suspension shock absorption system, factory-preset filter parameters and a built-in capacitor (no external capacitor required). ESC: SPECTER 60A 3-6S, STM32G071 (128K), BL32 firmware, 60A continuous / 65A (10 s) burst current. The stack measures 44.2x30x21.15mm and weighs ~39.24g without accessories and ~87g with accessories.

Box contents

  • Available visually
STACK: HGLRC SPECTER F760 BOX integrated stack Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU (FC):
    STM32F722 (216MHz)
    IMU(Gyro)(FC):
    MPU6000
    USB Port Type (FC):
    Type-C
    Barometer (FC):
    BMP280
    OSD Chip (FC):
    AT7456E
    BLE Bluetooth (FC):
    Built-in (UART5, Betaflight tuning via SpeedyBee APP)
    DJI Air Unit Connection Way (FC):
    Plug-and-play connector (SH1.0-7P / SH1.0-6P DJI cable included)
    6-pin DJI Air Unit Plug (FC):
    Supported
    Flash(for BlackBox) (FC):
    16MB
    BetaFlight Camera Control Pad (FC):
    Not specified
    Power Input (FC):
    7.4V-22.8V (2-6S LiPo)
    5V Output (FC):
    5V 2A (5V 2.5A on the spec sheet image)
    9V Output (FC):
    10V 2A (electronic switch, on/off via Betaflight)
    3.3V Output (FC):
    Not specified
    4.5V Output (FC):
    Not specified
    ESC Signal Pads (FC):
    Not specified
    UART (FC):
    4 UARTs
    ESC Telemetry UART (FC):
    Not specified
    LED Pad (FC):
    Yes (Buzzer/LED connector)
    Buzzer (FC):
    Yes (BB- / 5V, Buzzer/LED connector)
    BOOT Button (FC):
    Not specified
    Supported Flight Controller Firmware (FC):
    Betaflight
    Firmware Target Name (FC):
    HGLRCF722 MINI V2
    Mounting (FC):
    20x20mm, M3
    Dimension (FC):
    37x34x9.8mm
    Weight (FC):
    ~39.24g (whole stack)
    Firmware (ESC):
    FC: HGLRCF722 MINI V2 (Betaflight) / ESC: BL32 (SPECTER60_G_128)
    PC Configurator Download Link (ESC):
    Not specified
    Continuous Current (ESC):
    60A
    Burst Current (ESC):
    65A (10 seconds)
    TVS Protective diode (ESC):
    Not specified
    External Capacitor (ESC):
    Built-in capacitor (no external required)
    ESC Protocol (ESC):
    DShot600/300/150, Oneshot125/42, MultiShot
    Power Input (ESC):
    3-6S
    Power Output (ESC):
    Not specified
    Current Sensor (ESC):
    Not specified
    ESC Telemetry (ESC):
    Not specified
    Mounting (ESC):
    20x20mm, M3
    Dimension (ESC):
    44x36x7mm
    Weight (ESC):
    Not specified separately (whole stack ~39.24g)