Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

SpeedyBee F405 V3 BLS 60A 30x30 FC&ESC Stack

Brand
Category: Stack
Kod: MS46891340
(Pending Review)
  • Power Input (FC and ESC): 3-6S LiPo
  • Continuous Current (ESC): 60A * 4
  • Mounting (FC and ESC): 30.5 x 30.5 mm (4 mm hole diameter)
  • Dimensions: (FC) 41.6(L) x 39.4(W) x 7.8(H)mm - (ESC) 45.6(L) * 44(W) *8mm(H)
  • Weight: (FC) 9.6g - (ESC) 23.5g
  • PWM Frequency Range: X

Detail

STM32F405 FC (better than F411), built-in 4-level battery life indicator, 4 GB Blackbox SD card slot for your flight logs, internal Bluetooth for wireless configuration with SpeedyBee app, and 4 group LED strip pads for your digital quad. TVS protective diode + Japanese made TDK SMT capacitors + external 1000uF low ESR capacitor for robust 60A 4-in-1 ESC, designed for durability and smooth flight.
* DJI Air Unit connector is fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.

Box contents

  • Visually available
1. Open STACK Manual in a New Tab
Click here to open the STACK Manual in a new tab
2. Download STACK Manual
Click here to download the STACK Manual
STACK: SpeedyBee F405 V3 BLS 60A 30x30 FC&ESC Stack Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU (FC):
    STM32F405
    IMU(Gyro)(FC):
    BMI270
    USB Port Type (FC):
    Type-C
    Barometer (FC):
    Built-in
    OSD Chip (FC):
    AT7456E chip
    BLE Bluetooth (FC):
    Supported. Used for flight controller configuration (MSP must be enabled at 115200 Baud on UART4)
    DJI Air Unit Connection Way (FC):
    Two supported paths: 6-pin connector or direct soldering.
    6-pin DJI Air Unit Plug (FC):
    Supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.
    Flash(for BlackBox) (FC):
    *Betaflight firmware requires the microSD card type to be Standard (SDSC) or High Capacity (SDHC), so extended capacity cards (SDXC) are not supported (Many high-speed U3 cards are SDXC). The card should also be formatted with FAT16 or FAT32 (recommended) file systems. You can use any SD card under 32 GB, but Betaflight can only recognize a maximum of 4 GB. We recommend using this 3rd party formatting tool and selecting "Overwrite Format" before formatting your card. Also, check here for recommended SD cards or purchase tested cards from our store.
    BetaFlight Camera Control Pad (FC):
    Yes (CC pad on the front)
    Power Input (FC):
    3S - 6S Lipo (via G, BAT pins/pads on the 8-pin connector or through the 8 pads on the bottom)
    5V Output (FC):
    9 groups of 5V output, four +5V pads and 1 BZ+ pad (used for Buzzer) on the front, and 4x LED 5V pads. Total current load is 2A.
    9V Output (FC):
    2 groups of 9V output, one +9V pad on the front and the other included in the bottom connector. Total current load is 2A.
    3.3V Output (FC):
    Supported. Designed for 3.3V input receivers. Current load up to 500mA.
    4.5V Output (FC):
    Supported. Designed for receiver and GPS module even when powered via FC USB port. Current load up to 1A.
    ESC Signal Pads (FC):
    M1 - M4 on the bottom, M5-M8 on the front.
    UART (FC):
    6 sets (UART1, UART2, UART3, UART4 (dedicated for Bluetooth connection)), UART5 (dedicated for ESC telemetry), UART6
    ESC Telemetry UART (FC):
    UART R5
    LED Pad (FC):
    Supported. 5V, G, and LED pads on the bottom front. Used for WS2812 LED controlled by Betaflight software.
    Buzzer (FC):
    5V Buzzer pads BZ+ and BZ-
    BOOT Button (FC):
    Supported. [A]. Hold the BOOT button and power on the FC at the same time to force the FC into DFU mode, for flashing firmware when this FC is bricked. [B]. When the FC is on and in idle mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors. By default, short pressing the BOOT button changes the LED viewing mode. Long pressing the BOOT button switches between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.
    Supported Flight Controller Firmware (FC):
    BetaFlight (Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
    Firmware Target Name (FC):
    SPEEDYBEEF405V3
    Mounting (FC):
    30.5 x 30.5 mm (4 mm hole diameter)
    Dimension (FC):
    41.6(L) x 39.4(W) x 7.8(H)mm
    Weight (FC):
    9.6g
    Firmware (ESC):
    BLHeli_S J-H-40
    PC Configurator Download Link (ESC):
    https://esc-configurator.com/
    Continuous Current (ESC):
    60A * 4
    Burst Current (ESC):
    80A(10s)
    TVS Protective diode (ESC):
    Yes
    External Capacitor (ESC):
    1000uF Low ESR Capacitor (Included in Package)
    ESC Protocol (ESC):
    DSHOT300/600
    Power Input (ESC):
    3-6S LiPo
    Power Output (ESC):
    VBAT
    Current Sensor (ESC):
    Supported (Scale=400 Offset=0)
    ESC Telemetry (ESC):
    Not Supported
    Mounting (ESC):
    30.5 x 30.5 mm (4 mm hole diameter)
    Dimension (ESC):
    45.6(L) * 44(W) *8mm(H)
    Weight (ESC):
    23.5g