TUR
SpeedyBee F405 V4 BLS 60A 30x30 FC&ESC Stack
- Power Input (FC and ESC): 3-6S LiPo
- Continuous Current (ESC): 60A * 4
- Mounting (FC and ESC): 30.5 x 30.5 mm (4 mm hole diameter)
- Dimensions: (FC) 41.6(L) x 39.4(W) x 7.8(H)mm - (ESC) 45.6(L) * 44(W) *8mm(H)
- Weight: (FC) 10.5g - (ESC) 23.5g
- PWM Frequency Range: X
Detail
STM32F405 FC (better than F411), built-in 4-level battery life indicator, 4 GB Blackbox SD card slot for your flight logs, 4 group LED strip pads with a DJI plug for your digital quad, and internal Bluetooth for wireless configuration with the SpeedyBee app. Don't forget the powerful 60A 4-in-1 ESC made with aluminum alloy heat sinks + TVS protective diode + high-quality SMD filtering capacitors + external 1000uF low ESR capacitor for durability and smooth flight.
* DJI Air Unit plug is fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.
Box contents
- Visually available
1. Open STACK Manual in a New Tab
Click here to open the STACK Manual in a new tab2. Download STACK Manual
Click here to download the STACK ManualSTACK: SpeedyBee F405 V4 BLS 60A 30x30 FC&ESC Stack Manual Connection Image
Open the Manual in a New Tab
MCU (FC):
STM32F405
IMU(Gyro)(FC):
ICM42688P
USB Port Type (FC):
Type-C
Barometer (FC):
Internal
OSD Chip (FC):
AT7456E chip
BLE Bluetooth (FC):
Supported. Used for flight controller configuration (must be enabled at 115200 Baud on UART4)
DJI Air Unit Connection Way (FC):
Supported in two ways: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug (FC):
Supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.
Flash(for BlackBox) (FC):
*Betaflight firmware requires the microSD card type to be Standard (SDSC) or High Capacity (SDHC) under 32 GB, thus extended capacity cards (SDXC) are not supported (Many high-speed U3 cards are SDXC). The microSD card should also be formatted in FAT16 or FAT32 (recommended). That is, you can use any SD card under 32 GB, but Betaflight can only recognize a maximum of 4 GB. We recommend using this third-party formatting tool and selecting ‘Overwrite Formatting’ before formatting your card. You can also check here for recommended SD cards or purchase tested cards from our store.
BetaFlight Camera Control Pad (FC):
Not specified
Power Input (FC):
3S - 6S Lipo (via 8-pin connector G, BAT pins/pads or 8 pads on the underside)
5V Output (FC):
9 group 5V output, four +5V pads at the front and one BZ+ pad (used for Buzzer) and 4x LED 5V pads. Total current load is 3A.
9V Output (FC):
2 group 9V output, one +9V pad at the front and the other included in a connector at the bottom. Total current load is 3A.
3.3V Output (FC):
Supported. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output (FC):
Supported. Designed for receivers and GPS modules even when powered via the FC USB port. Up to 1A current load.
ESC Signal Pads (FC):
On the underside M1 - M4, on the front M5-M8.
UART (FC):
6 sets (UART1, UART2, UART3, UART4 (dedicated for Bluetooth connection)), UART5 (dedicated for ESC telemetry), UART6
ESC Telemetry UART (FC):
UART R5
LED Pad (FC):
Supported. 5V, G, and LED pads on the bottom front. Used for WS2812 LEDs controlled by Betaflight software.
Buzzer (FC):
BZ+ and BZ- pads used for 5V Buzzer
BOOT Button (FC):
Supported. [A]. Press and hold the BOOT button and power the FC at the same time, forces the FC into DFU mode, used for flashing firmware when the FC is bricked. [B]. While the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors at the bottom. By default, short-pressing the BOOT button changes the LED display mode. Long-pressing the BOOT button switches between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.
Supported Flight Controller Firmware (FC):
BetaFlight (Default), INAV
Firmware Target Name (FC):
SPEEDYBEEF405V4
Mounting (FC):
30.5 x 30.5 mm (4 mm hole diameter)
Dimension (FC):
41.6(L) x 39.4(W) x 7.8(H)mm
Weight (FC):
10.5g
Firmware (ESC):
BLHeli_S J-H-40
PC Configurator Download Link (ESC):
https://esc-configurator.com/
Continuous Current (ESC):
60A * 4
Burst Current (ESC):
80A (10 s)
TVS Protective diode (ESC):
Yes
External Capacitor (ESC):
1000uF Low ESR Capacitor (Included in Package)
ESC Protocol (ESC):
DSHOT300/600
Power Input (ESC):
3-6S LiPo
Power Output (ESC):
VBAT
Current Sensor (ESC):
Supported (Scale=400 Offset=0)
ESC Telemetry (ESC):
Not supported
Mounting (ESC):
30.5 x 30.5 mm (4 mm hole diameter)
Dimension (ESC):
45.6(L) * 44(W) *8mm(H)
Weight (ESC):
