Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

SpeedyBee F7 V2 BL32 45A Stack (with V22 ESC)

Brand
Category: Stack
Kod: MS46891340
(Review Pending)
  • Power Input (FC and ESC): 3-6S LiPo
  • Continuous Current (ESC): 45A * 4
  • Mounting (FC and ESC): 30.5 x 30.5 mm, 4 mm hole size
  • Dimensions: (FC) 41 x 38 x 6.9mm - (ESC) 41 * 45 * 6.5mm
  • Weight: (FC) 9g - (ESC) 12.5g
  • PWM Frequency Range: X

Detail

SpeedyBee F7 V2 BL32 45A Stack (with V22 ESC)
WARNING: For previous V2/V21 ESC groups, if you are running BLHeli32 Rev32.8 firmware, please do not enable bi-directional DShot in Betaflight. Make sure to upgrade to Rev32.9 firmware to use the bi-directional DShot feature. There are no issues with V22 ESC
Supported Motor: Requires 1900KV or lower for 6S

Box contents

  • Visually available
STACK: SpeedyBee F7 V2 BL32 45A Stack (with V22 ESC) Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU (FC):
    STM32F722
    IMU(Gyro)(FC):
    MPU6000
    USB Port Type (FC):
    Type-C
    Barometer (FC):
    BMP280 (I2C) Warning: Do not apply conformal coating over the barometer as the air hole may become blocked.
    OSD Chip (FC):
    BetaFlight OSD w/ AT7456E chip
    BLE Bluetooth (FC):
    Supported, used for flight controller configuration
    DJI Air Unit Connection Way (FC):
    There is a complete DJI Air Unit JST socket on board
    6-pin DJI Air Unit Plug (FC):
    Not specified
    Flash(for BlackBox) (FC):
    16MB built-in data flash
    BetaFlight Camera Control Pad (FC):
    Yes (CC pad)
    Power Input (FC):
    3-6S
    5V Output (FC):
    5V output x 7, with 6 pads and a pad for Buzzer (BZ+) totaling a maximum load current of 2.5A.
    9V Output (FC):
    2 x 9V outputs, 1 pad and 1 pad used for 1 DJI slot, with a total maximum load current of 2.5A.
    3.3V Output (FC):
    1 * 3.3V output pad, maximum load current 500mA.
    4.5V Output (FC):
    1 * 4.5V output pad
    ESC Signal Pads (FC):
    M1 - M4
    UART (FC):
    Full UART * 5 (UART1, UART2, UART3, UART5, UART6)
    ESC Telemetry UART (FC):
    UART4 RX
    LED Pad (FC):
    Used for WS2812 LED
    Buzzer (FC):
    BZ+ and BZ- pads used for 5V Buzzer
    BOOT Button (FC):
    Used for easy entry into DFU mode
    Supported Flight Controller Firmware (FC):
    BetaFlight (Default), EMUFlight
    Firmware Target Name (FC):
    SPEEDYBEEF7V2
    Mounting (FC):
    30.5 x 30.5 mm, 4 mm hole size
    Dimension (FC):
    41 x 38 x 6.9mm
    Weight (FC):
    9g
    Firmware (ESC):
    BLHeli32 SpeedyBee 4in1
    PC Configurator Download Link (ESC):
    Not specified
    Continuous Current (ESC):
    45A * 4
    Burst Current (ESC):
    55A (10 seconds)
    TVS Protective diode (ESC):
    Not specified
    External Capacitor (ESC):
    Not specified
    ESC Protocol (ESC):
    DSHOT300/600/1200
    Power Input (ESC):
    3-6S Note: It is highly recommended to solder the filtering capacitor between VBAT "+" and "-".
    Power Output (ESC):
    VBAT
    Current Sensor (ESC):
    Supported (Scale 168)
    ESC Telemetry (ESC):
    Supported
    Mounting (ESC):
    30.5 x 30.5 mm, 4 mm hole size
    Dimension (ESC):
    30.5 x 30.5 mm, 4 mm hole size
    Weight (ESC):
    12.5g