Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

GEPRC TAKER F722 BLS 80A 8S STACK

Brand
Category: Stack
Kod: MS46891340
(Review Pending)
  • Power Input: 3-8S LiPo
  • Continuous Current (ESC): 80A
  • Mounting (FC and ESC): 30.5x30.5mm
  • MCU: STM32F722
  • BEC: 5V@3A + 12V@3A
  • Burst Current (ESC): 85A (5 seconds)

Detail

The GEPRC TAKER F722 BLS 80A 8S STACK is an 8S-capable stack made of the TAKER F722 8S flight controller with an STM32F722 processor and the TAKER H80_8S_BLS 80A 4in1 ESC. Flight controller: ICM42688-P gyro (SPI), 16MB Blackbox, barometer, integrated LC filter, Type-C USB, direct plug-in connector for the DJI Air Unit, BetaFlight OSD (AT7456E), dual independent BEC (5V@3A + 12V@3A), 6 UARTs, 8 motor outputs, input 3-8S LiPo, size 38.5x38.5mm, mounting 30.5x30.5mm, firmware target GEPRC_TAKER_F722_8S. ESC: TAKER H80_8S_BLS 80A 4in1, input 3-8S LiPo, ammeter, 80A continuous, 85A burst (5 s), DShot150/300/600, size 56.3x61.1mm, 30.5x30.5mm mounting (φ4mm hole, φ3mm with silicone dampers), weight 28.3g, ESC target B_X_30. The damped mounting keeps the gyro stable.

Box contents

  • 1 x flight controller, 1 x TAKER H80_8S_BLS 80A 4in1 ESC, 1 x filter board (dual 50V 2200uF), DJI connection cable (SH1.0 6pin 100mm), 2 x FC adapter cable (SH1.0 8pin 30mm), receiver cable (SH1.0 4pin 150mm), camera cable (SH1.0-SH1.25 3pin 135mm), VTX cable (SH1.0 4-6pin 100mm), 1 x XT90 battery plug, red and black power cable (10AWG 240mm), 4 x M3*30 and 4 x M3*25 screws, 8 x M3 nylon nuts, 12 x M3 silicone anti-shake pads
1. Open STACK Manual in a New Tab
Click here to open the STACK Manual in a new tab
2. Download STACK Manual
Click here to download the STACK Manual
STACK: GEPRC TAKER F722 BLS 80A 8S STACK Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU (FC):
    STM32F722
    IMU(Gyro)(FC):
    ICM42688-P
    USB Port Type (FC):
    Type-C
    Barometer (FC):
    Supported
    OSD Chip (FC):
    AT7456E
    BLE Bluetooth (FC):
    No
    DJI Air Unit Connection Way (FC):
    DJI Air Unit plug-and-play connector
    6-pin DJI Air Unit Plug (FC):
    Supported
    Flash(for BlackBox) (FC):
    16MB
    BetaFlight Camera Control Pad (FC):
    Not specified by manufacturer
    Power Input (FC):
    3-8S LiPo
    5V Output (FC):
    5V@3A
    9V Output (FC):
    12V@3A
    3.3V Output (FC):
    Not specified by manufacturer
    4.5V Output (FC):
    Not specified by manufacturer
    ESC Signal Pads (FC):
    8 motor outputs (M1-M8)
    UART (FC):
    6 UARTs
    ESC Telemetry UART (FC):
    Not specified by manufacturer
    LED Pad (FC):
    Not specified by manufacturer
    Buzzer (FC):
    Not specified by manufacturer
    BOOT Button (FC):
    Not specified by manufacturer
    Supported Flight Controller Firmware (FC):
    Betaflight
    Firmware Target Name (FC):
    GEPRC_TAKER_F722_8S
    Mounting (FC):
    30.5x30.5mm
    Dimension (FC):
    38.5x38.5mm
    Weight (FC):
    Not specified by manufacturer
    Firmware (ESC):
    FC: GEPRC_TAKER_F722_8S / ESC: B_X_30 (BLHeli_S)
    PC Configurator Download Link (ESC):
    https://github.com/betaflight/betaflight-configurator/releases
    Continuous Current (ESC):
    80A
    Burst Current (ESC):
    85A (5 seconds)
    TVS Protective diode (ESC):
    Not specified by manufacturer
    External Capacitor (ESC):
    Filter board included (dual 50V 2200uF)
    ESC Protocol (ESC):
    DShot150/300/600
    Power Input (ESC):
    3-8S LiPo
    Power Output (ESC):
    Not specified by manufacturer
    Current Sensor (ESC):
    Supported (ammeter)
    ESC Telemetry (ESC):
    No (BLHeli_S ESCs do not support telemetry)
    Mounting (ESC):
    30.5x30.5mm (φ4mm hole, φ3mm with silicone dampers)
    Dimension (ESC):
    56.3x61.1mm
    Weight (ESC):
    28.3g