Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

HGLRC H743 8S MINI V1 FC

Brand
Category: FC (Flight Controller)
Kod: MS46891340
(Review Pending)
  • Power Input: 2S - 8S LiPo (7.4-33.6V)
  • Mounting: 20x20mm (M3)
  • Dimensions: 42x25mm
  • Weight: 6.8g
  • USB Port Type: Type-C
  • MCU (Microcontroller Unit): STM32H743

Detail

The HGLRC H743 8S MINI V1 is a 20x20mm flight controller whose ultra-narrow size and dual BEC design let it fit small frames (compatible with the HGLRC Nblade). It features a high-performance STM32H743 processor, ICM42688P gyro, AT7456E OSD, SPA06-003 barometer and a 16MB black box. It supports 2S-8S (7.4-33.6V) high-voltage input. It has a fully modular plug-and-play design with direct connectors; no soldering required. The VTX/VIN output voltage can be selected as 5V, VIN or 10V with a solder bridge. It has 8 UARTs and a DFU button. Firmware: HGLRC_H743_LITE. Weight is 6.8g; ~22.9g including the package. Package contents: FC, ESC (SH1.0-8P), receiver, camera, DJI, VTX and GPS cables, 8 vibration damping standoffs, HGLRC sticker and QR code card. On the website it is sold on the same page as the 60A 4in1 6S MINI ESC; the FC can be purchased separately.

Box contents

1. Open FC Manual in a New Tab
Click here to open the FC Manual in a new tab
2. Download FC Manual
Click here to download the FC Manual
FC: HGLRC H743 8S MINI V1 FC Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU:
    STM32H743
    IMU(Gyro):
    ICM42688P
    USB Port Type:
    Type-C
    Barometer:
    SPA06-003
    OSD Chip :
    AT7456E
    BLE Bluetooth :
    Not specified
    DJI Air Unit Connection Way :
    Plug-and-play VTX connector (VIN, GND, TX1, RX1, GND, RX7, VTX) + DJI cable included
    6-pin DJI Air Unit Plug :
    Supported
    Flash(for BlackBox) :
    16MB
    BetaFlight Camera Control Pad :
    Not specified
    Power Input :
    2S-8S LiPo (7.4-33.6V)
    5V Output :
    Dual BEC (value not specified)
    9V Output :
    10V (VIN output selectable 5V / VIN / 10V via solder bridge)
    3.3V Output :
    Not specified
    4.5V Output :
    Not specified
    ESC Signal Pads :
    1x 4in1 ESC connector (SH1.0-8P, M1-M4)
    UART :
    8 UARTs
    ESC Telemetry UART :
    UART8 (RX8)
    LED Pad :
    Yes (LED)
    Buzzer :
    Yes (BB-)
    BOOT Button :
    Yes (DFU button)
    Supported Flight Controller Firmware :
    Betaflight
    Firmware Target Name :
    HGLRC_H743_LITE
    Mounting :
    20x20mm, M3
    Dimension :
    42x25mm
    Weight:
    6.8g