Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

FETtec FC F7

Brand
Category: FC ( Flight Controller)
Kod: MS46891340
(Review Pending)
  • Power Input: 2S - 6S LiPo (6-27V)
  • Mounting: 20x20mm or 30x30mm (breakable corners)
  • Dimensions: 35*30*7.9mm
  • Weight: 5.37g
  • USB Port Type: USB (exact type not specified)
  • MCU (Microcontroller Unit) (Brain): STM32F7RET6 @ 216MHz

Detail

The FETtec FC F7 is a KISS-licensed flight controller that comes with KISS FC v2 firmware by default and can optionally be flashed with FETtec Alpha FC firmware. It uses an STM32F7RET6 (216MHz) processor and an MPU6000 gyro. It features a rare dual mounting pattern: 20x20mm (expandable from M2 to M3) OR, by breaking off the corners, it can be used with a 30x30mm mounting hole spacing. It features a dedicated 5V BEC for the VTX (max. 600mA) and true Pit Mode support for the Unify Nano. An 8-pin connector provides solderless ESC connection (expandable to up to 6/8 motors using a second 8-pin connector). Note: The product is currently shown as out of stock on the manufacturer's own website.

Box contents

1. Open FC Manual in a New Tab
Click here to open the FC Manual in a new tab
2. Download FC Manual
Click here to download the FC Manual
FC: FETtec FC F7 Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU:
    STM32F7RET6 (216MHz)
    IMU(Gyro):
    MPU6000
    USB Port Type:
    USB (exact port type not specified)
    Barometer:
    None (no information about a barometer feature in the manual)
    OSD Chip :
    Not Specified (digital OSD/VCS possible via serial3, but no dedicated OSD chip model specified)
    BLE Bluetooth :
    Not Specified
    DJI Air Unit Connection Way :
    Compatible with DJI/Caddx/Runcam Vista and O3 Air Unit (connection diagram available, connector type/pin count not detailed in the text)
    6-pin DJI Air Unit Plug :
    Not Specified
    Flash(for BlackBox) :
    Not Specified
    BetaFlight Camera Control Pad :
    Not Specified (uses KISS FC v2 / FETtec Alpha firmware rather than Betaflight; SmartAudio/Tramp possible via TX1)
    Power Input :
    2S - 6S LiPo (6-27V)
    5V Output :
    5V (dedicated for VTX, max. 600mA)
    9V Output :
    None
    3.3V Output :
    Yes (3.3V pin available on SER3 connector, current rating not specified)
    4.5V Output :
    Not Specified
    ESC Signal Pads :
    Signal 1-4 (solder pads on each corner + 8-pin connector); up to Signal 5-8 with the second 8-pin connector (for 6/8-motor aircraft)
    UART :
    5 UARTs (UART1 unused, UART2 for receiver, UART3 unused, UART4 for internal use, UART5 for ESC/telemetry/OneWire)
    ESC Telemetry UART :
    UART5 (shared with ESC telemetry / OneWire)
    LED Pad :
    Yes (RGB LED PWM pin on SER1, compatible with WS2812 LED strips)
    Buzzer :
    Buzzer pad available (pad details not specified)
    BOOT Button :
    Yes (Reset button, resets the FC to the preloaded bootloader)
    Supported Flight Controller Firmware :
    KISS FC v2 (default), FETtec Alpha FC firmware (flashable)
    Firmware Target Name :
    Not Specified (no Betaflight target; uses KISS FC v2 / FETtec Alpha firmware)
    Mounting :
    20x20mm (M2, expandable to M3) or 30x30mm mounting hole spacing (usable with breakable corners) — dual mounting pattern
    Dimension :
    35 x 30 x 7.9 mm (excluding 30x30 corners)
    Weight:
    5.37 g