Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

SpeedyBee F7 V3 Flight Controller

Brand
Category: FC ( Flight Controller)
Kod: MS46891340
(Evaluation is expected)
  • Power Input: 3S - 6S Lipo
  • Mounting: 30.5 x 30.5 mm (4 mm hole diameter)
  • Dimensions: 41(L) x 38(W) x 8.1(H) mm
  • Weight: 10.7g
  • USB Port Type: Type-C
  • MCU(Microcontroller Unit)(Brain): STM32F722

Detail

Hate soldering? Just plug them all in!
It’s 2022, so having a plug vs soldering option is a must! Plug in your digital video transmitter, receiver, camera, VTX, and GPS to complete your build in no time. Also comes with 4x LED plugs so you can light up your quad with no headache. Prefer soldering? Just flip the board and start working on it.

Box contents

  • Available in Visual
1. Open FC Manual in a New Tab
Click here to open the FC Manual in a new tab
2. Download FC Manual
Click here to download the FC Manual
FC: SpeedyBee F7 V3 Flight Controller Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU:
    STM32F722
    IMU(Gyro):
    BMI270
    USB Port Type:
    Type-C
    Barometer:
    BMP280
    OSD Chip :
    AT7456E chip
    BLE Bluetooth :
    Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip
    DJI Air Unit Connection Way :
    Two ways supported: 6-pin connector or direct soldering.
    6-pin DJI Air Unit Plug :
    Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
    Flash(for BlackBox) :
    500MB
    BetaFlight Camera Control Pad :
    Yes(CC pad on the front side)
    Power Input :
    3S - 6S Lipo
    5V Output :
    10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
    9V Output :
    2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
    3.3V Output :
    Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
    4.5V Output :
    Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
    ESC Signal Pads :
    M1 - M4 on bottom side and M5-M8 on front side.
    UART :
    5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
    ESC Telemetry UART :
    R4(UART4)
    LED Pad :
    Used for WS2812 LED controlled by Betaflight firmware.
    Buzzer :
    BZ+ and BZ- pad used for 5V Buzzer
    BOOT Button :
    Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
    Supported Flight Controller Firmware :
    BetaFlight(Default),INAV
    Firmware Target Name :
    SPEEDYBEEF7V3
    Mounting :
    30.5 x 30.5mm( 4mm hole diameter)
    Dimension :
    41(L) x 38(W) x 8.1(H)mm
    Weight:
    10.7g