Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Electronics Black Wrist Watch
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb
Product Thumb

HOBBYWING RTF F7 FC 8S Lite V2

Brand
Category: FC ( Flight Controller)
Kod: MS46891340
(Review Pending)
  • Input Voltage: 4S - 8S LiPo (12 - 35.6V)
  • Mounting: 30.5*30.5/φ4mm
  • Dimensions: 35*35*7.7mm
  • Weight: 10.4g
  • USB Port Type: Type-C
  • MCU (Microcontroller Unit)(Brain): STM32F722

Detail

RTF F7 FC 8S Lite V2 is the improved version of Hobbywing’s F722-core FPV flight controller with 6 independent UARTs. Difference from V1: an LDO (low-dropout regulator) circuit placed in front of the gyro sensor to reduce electrical noise, dual-voltage BEC output of 5V 3A & 12V 3A, and 6 dedicated plug-and-play ports for ELRS receiver, GPS, LED, servo, VTX and ESC. It comes with integrated 16MB Blackbox flash memory, a high-precision Goertek barometer and vibration-damping rubber mounts.

Box contents

1. Open FC Manual in a New Tab
Click here to open the FC Manual in a new tab
2. Download FC Manual
Click here to download the FC Manual
FC: HOBBYWING RTF F7 FC 8S Lite V2 Manual Connection Image
Open the Manual in a New Tab Manual Connection Image
    MCU:
    STM32F722
    IMU(Gyro):
    ICM42688P (with LDO-supported noise reduction circuit)
    USB Port Type:
    Type-C
    Barometer:
    Goertek high-precision barometer (exact model number not specified)
    OSD Chip :
    AT7456E
    BLE Bluetooth :
    Not Specified
    DJI Air Unit Connection Way :
    DJI O4 Air Unit Pro connection via 8-pin ribbon cable (HD video link voltage: 7.4-26.4V); according to official sources, plug-and-play compatible with Analog and DJI digital VTX systems (Walksnail/HDZero compatibility is not specified in official sources for this product)
    6-pin DJI Air Unit Plug :
    Not Specified
    Flash(for BlackBox) :
    16 MB
    BetaFlight Camera Control Pad :
    Not Specified
    Power Input :
    4S - 8S LiPo (12 - 35.6V)
    5V Output :
    5V 3A
    9V Output :
    None (12V 3A output is available instead)
    3.3V Output :
    Not Specified
    4.5V Output :
    Not Specified
    ESC Signal Pads :
    M1 - M4 (default), plus CH5 and CH6 for up to 6 motor signals in total
    UART :
    6 independent UARTs
    ESC Telemetry UART :
    Not Specified
    LED Pad :
    LED control supported (separate LED pins available, pad name not specified)
    Buzzer :
    Buzzer (beeper) supported (pad details not specified)
    BOOT Button :
    BOOT pin available (for DFU/firmware flashing; detailed usage not specified)
    Supported Flight Controller Firmware :
    Betaflight (factory-installed version 4.5.2)
    Firmware Target Name :
    HOBBYWING_XROTORF7CONV
    Mounting :
    30.5 x 30.5 mm (φM4 — according to the product page; listed as M3 in the official PDF manual)
    Dimension :
    35.0 x 35.0 x 7.7 mm
    Weight:
    10.4 g