TUR
SpeedyBee F405 V4 30x30 Flight Controller
- Power Input: 3S - 6S Lipo
- Mounting: 30.5 x 30.5 mm (4 mm hole diameter)
- Dimensions: 41.6(L) x 39.4(W) x 7.8(H)mm
- Weight: 10.5g
- USB Port Type: Type-C
- MCU (Microcontroller Unit): STM32F405
Detail
ICM42688P Gyro and clean power supply. MaxLinear’s reputable LDO power chip enhances jitter protection by 320%. A 100uF filtered tantalum capacitor protects the gyro data from power noise. This provides precise flight response and truly enhances your flying experience!
Box contents
- Visually available
1. Open FC Manual in a New Tab
Click here to open the FC Manual in a new tab2. Download FC Manual
Click here to download the FC ManualMCU:
STM32F405
IMU(Gyro):
ICM42688P
USB Port Type:
Type-C
Barometer:
Included
OSD Chip :
AT7456E chip
BLE Bluetooth :
Supported. Used for configuring the Flight Controller (must be activated at 115200 baud rate on UART4)
DJI Air Unit Connection Way :
Two supported paths: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug :
Supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.
Flash(for BlackBox) :
*Betaflight firmware requires that the microSD card type be below 32 GB Standard (SDSC) or High Capacity (SDHC), so extended capacity cards (SDXC) are not supported (Many high-speed U3 cards are SDXC). Also, the microSD card must be formatted in FAT16 or FAT32 (recommended) format; you can use any SD card below 32 GB, but Betaflight can only recognize a maximum of 4 GB. We recommend using this third-party formatting tool and selecting "Overwrite Formatting" and then formatting your card. You can also check here for recommended SD cards or purchase tested cards from our store.
BetaFlight Camera Control Pad :
Not specified
Power Input :
3S - 6S Lipo (via G, BAT pins/pads on the 8-pin connector or the 8 pads on the bottom)
5V Output :
9 group 5V output, with four +5V pads on the front and 1 BZ+ pad (used for Buzzer) and 4x LED 5V pads. Total current load is 3A.
9V Output :
2 group 9V output, one +9V pad on the front and the other included on a connector at the bottom. Total current load is 3A.
3.3V Output :
Supported. Designed for 3.3V input receivers. Current load up to 500mA.
4.5V Output :
Supported. Designed for receivers and GPS modules even when powered through the FC USB port. Current load up to 1A.
ESC Signal Pads :
At the bottom: M1 - M4, at the front: M5-M8.
UART :
6 sets (UART1, UART2, UART3, UART4 (dedicated for Bluetooth connection)), UART5 (dedicated for ESC telemetry), UART6
ESC Telemetry UART :
UART R5 (UART5)
LED Pad :
Supported. 5V, G, and LED pads at the bottom of the front. Used for WS2812 LED controlled by Betaflight software.
Buzzer :
5V pads used for Buzzer: BZ+ and BZ- pad
BOOT Button :
Supported. [A]. Press and hold the BOOT button and turn on the FC at the same time, forcing the FC into DFU mode, for flashing the firmware if the FC becomes bricked. [B]. When the FC is on and in idle mode, the BOOT button can be used to control LED strips connected to the LED1-LED4 connectors at the bottom. By default, briefly pressing the BOOT button will change the LED viewing mode. Long-pressing the BOOT button switches between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.
Supported Flight Controller Firmware :
BetaFlight (Default), INAV
Firmware Target Name :
SPEEDYBEEF405V4
Mounting :
30.5 x 30.5 mm (4 mm hole diameter)
Dimension :
41.6(L) x 39.4(W) x 7.8(H)mm
Weight:
