TUR
SpeedyBee F405 V3 30x30 Flight Controller
- Power Input: 3S - 6S LiPo
- Mounting: 30.5 x 30.5 mm (4 mm hole diameter)
- Dimensions: 41.6(L) x 39.4(W) x 7.8(H) mm
- Weight: 9.6g
- USB Port Type: Type-C
- MCU (Microcontroller Unit) (Brain): STM32F405
Detail
You know it, right? For just $69.99, you will get an STM32F405 FC (better than F411), built-in 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 group LED strip pads, a DJI plug* for your digital quad and internal Bluetooth for wireless configuration with the SpeedyBee app. Don't forget the powerful 50A 4-in-1 ESC made with a TVS protective diode + Japan-made TDK SMT capacitors + external 1000uF low ESR capacitor, all built for durable structure and smooth flights. All this for just $69.99! Top-tier features at an incredibly low price, what are you waiting for? * DJI Air Unit plug is fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.
Box contents
- Visually Available
1. Open FC Manual in a New Tab
Click here to open the FC Manual in a new tab2. Download FC Manual
Click here to download the FC ManualMCU:
STM32F405
IMU(Gyro):
BMI270
USB Port Type:
Type-C
Barometer:
Included
OSD Chip :
AT7456E chip
BLE Bluetooth :
Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please ensure that the MSP switch on UART 4 is turned on and set to 115200 baud rate; otherwise, the Bluetooth function will not be available.
DJI Air Unit Connection Way :
Supported two ways: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug :
Supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no cables need to be replaced.
Flash(for BlackBox) :
*Betaflight firmware requires the microSD card type to be Standard (SDSC) or High Capacity (SDHC), so extended capacity cards (SDXC) are not supported (Many high-speed U3 cards are SDXC). Additionally, the card should be formatted with FAT16 or FAT32 (recommended) file systems. This means you can use any SD card less than 32GB, but Betaflight can only recognize a maximum of 4GB. We recommend using this 3rd-party formatting tool and selecting Overwrite formatting and then formatting your card. You can also check here for recommended SD cards or purchase tested cards from our store.
BetaFlight Camera Control Pad :
Yes (CC pad on the front)
Power Input :
3-6S LiPo. The flight controller is powered through the G, V wires of the 8-pin cable or the G, V pads on the bottom side of the flight controller.
5V Output :
9 groups of 5V output, four +5V pads on the front and one BZ+ pad (used for Buzzer) and 4x LED 5V pads. Total current load is 2A.
9V Output :
2 groups of 9V output, one +9V pad on the front and the other included in a connector on the bottom. Total current load is 2A.
3.3V Output :
Supported. Designed for 3.3V input receivers. Current load up to 500mA.
4.5V Output :
Supported. Designed for receivers and GPS modules even when powered through the FC USB port. Current load up to 1A.
ESC Signal Pads :
On the bottom M1 - M4, on the front M5-M8.
UART :
6 sets (UART1, UART2, UART3, UART4 (dedicated for Bluetooth connection), UART5 (dedicated for ESC telemetry), UART6
ESC Telemetry UART :
UART R5 (UART5)
LED Pad :
Supported. 5V, G and LED pads on the bottom front. Used for WS2812 LED controlled by Betaflight software.
Buzzer :
BZ+ and BZ- pad used for 5V Buzzer
BOOT Button :
Supported. [A]. Hold down the BOOT button and power on the FC at the same time, forcing the FC into DFU mode, this is for flashing the firmware when the FC gets bricked. [B]. When the FC is on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom. By default, briefly press the BOOT button to change the LED viewing mode. Long press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.
Supported Flight Controller Firmware :
BetaFlight (Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
Firmware Target Name :
SPEEDYBEEF405V3
Mounting :
30.5 x 30.5 mm (4 mm hole diameter)
Dimension :
41.6(L) x 39.4(W) x 7.8(H) mm
Weight:
